Відео

Hello. My lock does not work and rarely works. When I opened it, I found the engine very hot. What is the solution, please? Thank you.

Will this work for a 2016 dodge journey?

Hello, which oil should be put for Sorento power take-off gearbox (off-road gearbox)?

Watching this video cause I have same problem

I have to replace this on my telluride. Any chance you have a video on how to pull this unit and install a replacement?

Great video and info. Terrible audio....

Any ideas? My 2014 Kia Cadenza has a push button start. Intermittently won't start when button is pressed. The dash does light up. I have changed the fob battery. My work around is pressing the starter button for 10-15 seconds. This has been going on for a couple of years. The dealership doesn't have cluse. Could it be a bad break switch? I'm not car tech savy. Thanks

this is a great method for a v configuration engine. I always thought you would need a known good waveform

Thank you so much. This is a tremendous blessing to me. God is so good.

Hi so I followed your directions but my Kia still won’t start

What is the difference between Add A key and Programm a Key.

I love my power probe just for that reason. It comes directly from battery and you always know which is power and ground. You can then check motor with direct power too . Great video

That was funny but accurate demonstration of surging 😁👊🏻

Nice and simple 👍. I really enjoyed it.

Can you do this with a used pcm using mazda mmp or do I need the whole ids software?

Multimeter test is completely wrong. You're basically relying on the fact that the more amount of water in the fluid conducts more electricity. However, multimeter reading would depend on the contact surface area of the fluid, the place you touch to chassis for ground, magnitude of the current multimeter uses to measure resistance. This test is multimeter model, prob type, car and operator dependent. It means it's completely BS.

Cable yellow do you use ?

is the programm still available?

Yotengo una denali hybrid que no aranca

Yo tengo una yukon denali hybrid no da marcha que sele podra acer es 2010

HI CAN YOU TEKK ME IF THIS UNIT HAS IN THE CRYSLER LIST RAM 1500 2020 OVER TANKS.

Should this P0017 engine cide be a recall as the dowel pin seems to be a common problem with hyundai elantra cars. what causes this issue and should Hyundai pay for the dianostic and repair?

If the vehicle don't start after all that, and I have checked the start relay, starter fuse and change the battery ,what can it be ?

Evening the car doesn't turn the engine on dash board is totally blank

Horrible video, we just have to sit and watch you work on a vehicle and explain nothing lol

I need to change mine, I've chewed through two belts already and I've spun the idler pulleys to test bearings, and everything else is fine. Must be my tensioner!

Hi i have sorento 2023 8k code p195800 tells me to change 4WD COUPLING ACTUATOR ASSEMBLY REPLACEMENT what happens if i will leave it with light on dash . and no torque in rear wheels!! any problems if i ignore it? thanks

was it hard removing the dash.

Subscribed and waiting for part 2

Can a used pcm be programmed? I have this same scenario in my shop right now.

ces dure de suive parce qu il y a un reflet qui se fait dans ton écran d ordi et de scanneur🤫

Good job. One thing, how can you concentrate with loud music in the back ground?

hola me llamo Enrique compre un obdprog 501 hace un ano y no e podido actualizar tu cres que puedas ayudarme,te lo agradeceria.GRacias

I have a car that day for a couple years after my kiddo slammed into the curb on the driver side. Finally got it back together but it won't go out of park.. any thoughts?

So what is the main problem. I've forti 2011 and some time didn't start at all One of the electrician say don't insert the remote?

👍👍👌👌✅️✅️

Enjoyable video Jeremy, always fun when others have had a go at it first:)

Greetings, I would like to give you some software that I have developed for waveform analysis. It is similar to "Pressure Waveform Overlay" but with better features and can be used in real time on oscilloscope software and works from Windows 7 to 11. I would like you to give me a means of contact such as email.

I don’t know what the password you put your self password

I enjoyed this video. I have several fourth gen Firebirds and I'm glad to see this one running again.

Great job so far. Had you done a lot of body work before you started working on the 05 truck? I bought a 2005 F150 last year but its previous owner had just put in a new engine. It runs great but has a lot of rust too. Haven't done body work in ages but used a lot of fiberglass and fill on an old MGB I bought as a kid. It ended up looking pretty nice and it's nice knowing, at least the fiberglass sections wouldn't rust out again. I was also really surprised how easy it was to work with... once you got the hang of it. Keep up the good work.

Is this something that affects the vehicle or just annoying?

I have FRPS circuit hight eror.engine cant start but at same time i have fuel pressure readings that goea up to1200 when cranking.but i am going to perform the test as shown

I have no control either if I use a scan tool I can control it to come on heater fan and everything but the heater control is dead not turning on heater or nothing can it be the body control module too I replace it with another heater control unit and did the same it’s not sending any power to come on

So glad I saw this, literally had the exact same issue happen to a 15 sorento, my diag took me to the pcm but I'm always so hesitant to call a pcm.

You call that a video?

shitty video. You're body and arms are in the way 1/2 the time. Should have been slightly more overhead view. !!

Does it has a fuse ?

Thanks. Do you have or any idea how to program a push start or proximity on OBDPROG?

how did you record your video with camera and your phone screen at the same time?